Polar Bear Air Conditioning & Heating Inc. Blog: Archive for March, 2012

Reasons Your Washington DC Heat Pump Can’t Maintain the Right Temperature

Monday, March 26th, 2012

When you set your thermostat for a certain temperature, you expect that your Washington DC heat pump will either heat or cool it to that temperature, right? When you want 72 degrees, you don’t expect to have the temperature stay stuck at 70 degrees while your heat pump struggles futilely.

Sometimes heat pumps have trouble maintaining the right temperature, especially in heating mode. It’s not uncommon, and it has a number of potential causes. Run through this checklist to see if it is something you can fix yourself:

  • The outdoor unit is iced up. Running a defrost cycle can usually fix this.
  • The outdoor unit is not running at all. Sometimes this is simple enough to fix on your own. Read the manufacturer’s instructions to troubleshoot the problem.
  • Too much cold air is getting in the house for the heat pump to keep up. Make sure your doors and windows are closed to keep that valuable heat inside.
  • Your vents are closed. It may seem obvious, but problems like this can sometimes be attributed to user error. Make sure your vents are open to allow heat in.

This is by no means an all-inclusive list, and it covers just those causes that you could potentially fix yourself. There are many other possible culprits out there that could be more sinister and require Washington DC heating and air conditioning professional to be properly repaired.

Some of these include:

  • The compressor is not running.
  • A compressor valve or reversing valve is faulty.
  • The thermostat is malfunctioning or needs to be recalibrated.
  • The refrigerant level is low or there is a problem with the flow of the refrigerant.
  • The heat pump needs routine maintenance.

If your heat pump is not working properly for several days, especially after you have tried some of the DIY solutions above, call Polar Bear Air Conditioning right away. Your heat pump may need repairs before a bigger problem develops.

Continue Reading

Tags: , ,
Posted in Heat Pumps | Comments Off on Reasons Your Washington DC Heat Pump Can’t Maintain the Right Temperature

Washington DC Heating Tip: Dangers of Not Changing Your Furnace Filter on Time

Wednesday, March 14th, 2012

Of the many ways to heat a home in Washington D.C., forced air systems are the simplest in function and the easiest to maintain.  They are so simple, in fact, it is easy to forget they need attention at all, but there are dangers to not changing your furnace filter on time that have a real and painful cost in efficiency and dollars.  Even health risks arise when filters have been neglected too long.

Contracting with a company like Polar Bear Air Conditioning ensures consistent maintenance and oversight to allow Washington D.C.  homeowners the comfort and relaxation you deserve in your own home.

Back to Basics

Usually in the basement or a central location, a furnace heats air to a temperature set by the thermostat.  Over the years, technological improvements have enabled furnaces to be much smaller and fit into closets instead of the large and gangly monsters of old that could fill an entire basement.

By a fan in the furnace, the warm air is circulated through filters into a system of ducts to be distributed to grates in the wall or registers on the floor.  A second grate and duct system returns cooler air back to the furnace to be reheated.

Water can be added at the furnace to humidify the air and filters are able to remove some of the dust that typically floats invisibly throughout a home.

The Dangers of Not Changing the Filter

When the system is properly maintained, it is clean, efficient and produces comforting heat on demand at the touch of the thermostat or consistently throughout the day and night.

The furnace filter is designed to remove dust from air as it passes through your furnace. The longer your furnace filter is in place the dirtier it becomes. The increase of particles caught in the filter creates resistance to air flow through the filter and reduces efficiency.

To make up for the loss of flow through a dirty filter, the heat exchanger, usually a gas or oil fired flame, must work harder to produce the same amount of heat to the space.  This becomes costly financially and causes undo wear and stress on the equipment, requiring a partial or full replacement much sooner.

Additionally, operating above ideal designed conditions, cracks in the chamber may appear from the over load which can allow carbon monoxide, a toxic gas, to be released into the duct work.  This gas in large quantities in the home can cause headaches, nausea, and in extreme circumstances, even death.

Regular Maintenance

To avoid problems and excessive strain, remember to change the filters at the beginning of each new heating season.  An annual maintenance, check-up and thorough cleaning by a qualified company like Polar Bear Air Conditioning ensures a safe and comfortable season of warmth with no need to worry about the dangers of not changing filters in your furnace.

Continue Reading

Tags: , ,
Posted in Heating | Comments Off on Washington DC Heating Tip: Dangers of Not Changing Your Furnace Filter on Time