Polar Bear Air Conditioning & Heating Inc. Blog: Archive for the ‘Heating’ Category

Washington DC Heating and Air Conditioning Contractor’s Guide: Basic HVAC Terminology

Monday, May 7th, 2012

Ever try to look up basic information about your Washington DC heating and air conditioning systems? There are dozens of terms that might as well be Greek for all you know – a mishmash of words and phrases talking about energy efficiency and air flow ratios. To make your next upgrade a little easier and give you a baseline with which to work, here are a few of the most common HVAC terms you’ll hear in the industry:

AFUE – Annual Fuel Utilization Efficiency – This is a simple measurement of how much fuel a furnace converts into actual heat in your home. So, if a furnace converts 92% of the fuel it consumes into heat, it has an AFUE rating of 92.
Watts – A single watt is a measurement of electricity. Commonly, your electricity use is assured in kilowatts or kilowatt hours (kWh).
BTU – British Thermal Unit – A BTU is a common measurement of how much energy is produced or consumed by an appliance. When referring to an air conditioner, one “ton” refers to 12,000 BTUs.
SEER/EER – Seasonal Energy Efficiency Ratio refers to how many BTUs can be produced with a single Watt of electricity per hour. So, an air conditioner with an SEER of 14 can produce 14 BTUs of cooling per watt consumed each hour.
HSPF – Heating Seasonal Performance Factor – Refers to the efficiency of the heating elements in your heat pump.
COP – Coefficient of Performance – A measurement of how effective your heat pump is at heating a space compared to standard electrical resistance heat. The lower the temperature gets outside, the lower the COP will be. Equipment is usually measured for COP at 47 and 17 degrees to give an idea of seasonal performance of a new heat pump.
Refrigerant – Refrigerant is any gas that is used to draw heat from the air in a particular environment through an air conditioner or heat pump. It has a much lower boiling point than water, allowing it to cool despite the temperature outside. Currently, most equipment uses R-22 refrigerant while the new standard will be R-410A (Puron), legally required in all cooling units by 2020.
CFM – Cubic Feet per Minute – Used to measure the volume of air passed through an air handler by an air conditioner or furnace.

There are a number of complicated details to keep track of when choosing a new air conditioner or furnace. To ensure you get the very best out of your Washington DC heating and cooling system, read up on these details in advance – you’ll feel a heck of a lot smarter when you call. For any HVAC service you need in the Washington DC area, give Polar Bear Air Conditioning a call!

Tags: Air Conditioning, Heating, HVAC, Washington DC
Posted in Air Conditioning, Heating | Comments Off on Washington DC Heating and Air Conditioning Contractor’s Guide: Basic HVAC Terminology

Washington DC Heating Tip: Dangers of Not Changing Your Furnace Filter on Time

Wednesday, March 14th, 2012

Of the many ways to heat a home in Washington D.C., forced air systems are the simplest in function and the easiest to maintain. They are so simple, in fact, it is easy to forget they need attention at all, but there are dangers to not changing your furnace filter on time that have a real and painful cost in efficiency and dollars. Even health risks arise when filters have been neglected too long.

Contracting with a company like Polar Bear Air Conditioning ensures consistent maintenance and oversight to allow Washington D.C. homeowners the comfort and relaxation you deserve in your own home.

Back to Basics

Usually in the basement or a central location, a furnace heats air to a temperature set by the thermostat. Over the years, technological improvements have enabled furnaces to be much smaller and fit into closets instead of the large and gangly monsters of old that could fill an entire basement.

By a fan in the furnace, the warm air is circulated through filters into a system of ducts to be distributed to grates in the wall or registers on the floor. A second grate and duct system returns cooler air back to the furnace to be reheated.

Water can be added at the furnace to humidify the air and filters are able to remove some of the dust that typically floats invisibly throughout a home.

The Dangers of Not Changing the Filter

When the system is properly maintained, it is clean, efficient and produces comforting heat on demand at the touch of the thermostat or consistently throughout the day and night.

The furnace filter is designed to remove dust from air as it passes through your furnace. The longer your furnace filter is in place the dirtier it becomes. The increase of particles caught in the filter creates resistance to air flow through the filter and reduces efficiency.

To make up for the loss of flow through a dirty filter, the heat exchanger, usually a gas or oil fired flame, must work harder to produce the same amount of heat to the space. This becomes costly financially and causes undo wear and stress on the equipment, requiring a partial or full replacement much sooner.

Additionally, operating above ideal designed conditions, cracks in the chamber may appear from the over load which can allow carbon monoxide, a toxic gas, to be released into the duct work. This gas in large quantities in the home can cause headaches, nausea, and in extreme circumstances, even death.

Regular Maintenance

To avoid problems and excessive strain, remember to change the filters at the beginning of each new heating season. An annual maintenance, check-up and thorough cleaning by a qualified company like Polar Bear Air Conditioning ensures a safe and comfortable season of warmth with no need to worry about the dangers of not changing filters in your furnace.

Tags: Air Filters, Heating Maintenance, Washington D.C.
Posted in Heating | Comments Off on Washington DC Heating Tip: Dangers of Not Changing Your Furnace Filter on Time

Washington DC HVAC Contractor Tip: Things You Can Do to Make Your Heating System More Effective

Wednesday, February 29th, 2012

Have you ever wondered why it is too hot or too cold in your Washington DC home? You can always blame it on the thermostat or an open or closed window. Those are easy targets. But maybe the real culprit is your heating and cooling system, namely your furnace or air conditioner. Maybe these pieces of equipment have to work extra hard because of something as simple as a dirty filter that you should have cleaned or replaced.

Learning how to make your heating and cooling system more “effective” does not require a physics degree or an extensive knowledge of the refrigeration cycle. In most cases, it just takes common sense – and a little creativity.

For example, did you know that how your home is insulated can have a direct impact on how well your heating and cooling equipment functions? It sure can. If your walls, crawl spaces, or attic is poorly insulated or not insulated at all, your furnace and air conditioner will have to work harder to keep up – and keep you warm or cool. In some cases, your heating and cooling equipment might never be able to give you the desired temperature on your thermostat setting because the equipment has to work too hard to make up for lost heat or cooling due to poor insulation.

So what should you do? Find out if your home is properly insulated by having a load calculation or energy audit on your home. Any licensed and qualified heating and cooling contractor will be able to perform one of these tasks for you and show you where you might be losing too much of your indoor air to poor insulation. This same test can also detect any leakage through cracks in the foundation or joints or connections in ductwork. Windows and skylights are also an area of heat loss or gain. Installing awnings or trees can cut down on this loss or gain, too.

Of course, the most effective heating and cooling system is one that is serviced and properly maintained on a regular basis. If you have any questions on system maintenance, call Polar Bear and schedule a tune-up today.

Tags: Energy Savings, Heating, Washington DC
Posted in Heating | Comments Off on Washington DC HVAC Contractor Tip: Things You Can Do to Make Your Heating System More Effective

Washington DC Heating Question: Can Your Heating System Warn You of a CO Leak?

Wednesday, February 22nd, 2012

As everyone in Washington knows, carbon monoxide is a serious health risk. It is an odorless gas that is produced as a natural byproduct of combustion. So, any time something burns, carbon monoxide (CO) is released into the air.

As long as the area is properly ventilated, the carbon monoxide cannot build up in the air to a dangerous level of concentration. For example, if you are around a campfire or charcoal that is burning outside, you are generally safe.

In the home, the danger arises when combustion is not properly ventilated and this toxic gas is allowed to seep into our living spaces. If you use any gas, fuel or wood burning appliances in your home, you are at risk for exposure to carbon monoxide. To help mitigate that risk, it is important to know some warning signs. Your heating system gives off some warnings that can tip you off to danger, so be on the lookout for these three signals:

Carbon monoxide detector goes off. Some heating systems these days have built-in carbon monoxide detectors, which can provide an extra measure of safety. Whether you have one of these systems or not, your home should still be equipped with a CO detector. If it begins sounding the alarm, get everyone out of the house immediately.

A fume vent is leaking. Fuel-burning furnaces have vents to move combustion gases out of the house safely. If you notice this vent is leaking on your heating system, CO may be seeping into your house. Shut down the furnace, open windows for ventilation and have the fume vent repaired immediately.

Smoke backing up from the fireplace. If you have a fireplace and you notice smoke in the room while using it, stop using it immediately. Your chimney may be blocked or leaking, preventing the smoke from rising and venting properly, which means CO can e getting into your house. Do not use the fireplace again until you have had the chimney inspected.

Please take care and note this is just a simple guide. There are other risks and warnings of carbon monoxide. If you have any suspicion that there is CO in your home, immediately call Polar Bear Air Conditioning to look into the situation.

Tags: Carbon Monoxide, CO, Heating Repair
Posted in Heating | Comments Off on Washington DC Heating Question: Can Your Heating System Warn You of a CO Leak?

Capitol Hill Heating Repair Question: What Are Flue Gas Spill Switches?

Wednesday, February 1st, 2012

While some components of a heating system make sense to the average homeowner in Capitol Hill – think blower fan, thermostat and air ducts – others are more esoteric and prone to bouts of head scratching.

So, you may find yourself asking “what the heck is a flue gas spill switch?”

As you know, gas heating appliances produce heat by means of combustion. The gas line feeds gas into the appliance, the gas is ignited, and the burning gas produces heat. It’s a simple concept that goes all the way back to our caveman ancestors building fires to keep warm, and it is the same process in gas furnaces, boilers and water heaters.

In addition to producing the cozy heat we love in the winter time, this combustion process also releases gases. Known collectively as “flue gases,” some of these – carbon monoxide being the most notorious – can be very toxic. This why we have flues or chimneys in our homes– to give these gases a means of egress.

A flue gas spill switch is designed to shut down the furnace if these gases start seeping out. It is made up of a sensor or series of sensors that detect heat outside the flue, not unlike the flame sensor in your furnace. If flue gases start to escape and pass by the sensor, the sensor heats up and signals the furnace to shut down. This cuts off the power and gas, so that no more flue gases can leak into the home and create a health concern.

If your furnace has been abruptly shutting down, it could be your flue gas spill switch trying to tell you that you have a leaky or cracked flue. If this is the case, you want to have it repaired right away. The constant off and on is not good for the furnace, and more importantly, those flue gases can be exceptionally hazardous to your family’s health.

Tags: Capitol Hill, Furnaces, Heating, Heating Repair, Washington DC
Posted in Heating | Comments Off on Capitol Hill Heating Repair Question: What Are Flue Gas Spill Switches?

Washington DC Heating Guide: Basic Boiler Maintenance

Wednesday, January 18th, 2012

The boiler in your Washington DC home is a sensitive piece of equipment that needs routine maintenance and repairs. Regularly maintaining your boiler is especially important for safety reasons. Many boiler malfunctions and accidents are due to neglecting some of these basic tasks.

Even if you’ve just installed a new boiler, the safety valves and settings should be checked by a professional on a regular basis to prevent a breakdown or hazard. We recommend that you schedule a boiler inspection and cleaning at least once a year. Call Polar Bear if you have any questions about boiler maintenance.

A service technician will measure the pressure, drain and remove sediment buildup, test the efficiency ratings, and make sure your boiler is set at the right temperatures. Regular maintenance can also help you determine whether or not you need a boiler replacement. By keeping track of performance levels, you will be able to tell when it’s time for an upgrade.

Other tasks performed during an annual maintenance visit include cleaning and lubricating all the components, checking for any leaks or clogs, and testing gas boilers for any carbon monoxide intrusion. If you have any gas appliances in your home, you should always have carbon monoxide detectors and test them once a month.

Boiler pressure is something that you can check often on your own. If you aren’t sure how to read the pressure gauge, or if you aren’t sure what the right pressure should be, just call one of our technicians to walk you through this process.

Always call Polar Bear if you have any problems with the boiler in your Washington DC home. We are here to help and answer any questions you may have.

Tags: Boiler Maintenance, Heating Maintenance, Washington DC
Posted in Heating | Comments Off on Washington DC Heating Guide: Basic Boiler Maintenance

Pros and Cons of Various Heating Systems in Washington DC

Wednesday, January 4th, 2012

When it comes time to install a new heating system in your Washington DC home, there are a lot of options to consider. Many people get overwhelmed when confronted with all of the furnaces, boilers and heat pumps on the market these days. So, to help you get a handle on what each has to offer and which will offer you the best benefits, here is an overview of the modern heating system market.

Furnaces

Furnaces are the core of a forced air heating system and use gas, oil or electricity to heat air which is then circulated through your home by a blower in your air handler. Furnaces are among the most fuel efficient heating systems on the market today with options available at up to 95% AFUE (meaning it uses up to 95% of the fuel consumed to produce heat). They are also inexpensive to install and while they don’t last quite as long as boilers, they are highly efficient when well cared for.

Boilers

Boilers use gas, oil or electricity to heat water or steam which is then circulated through your home into radiators or baseboard heaters. The heated water or steam releases heat into your home and heats it in turn. While not quite as energy efficient as a high efficiency furnace, boiler heat is perfect for homes with existing radiators and no room for vents and ductwork. It also has less of an impact on indoor air quality since there is no air movement and boilers tend to last a very long time when well maintained.

Heat Pumps

Heat pumps are becoming increasingly popular, especially in milder climates where it rarely gets below 40 degrees F. A heat pump uses the same technology as an air conditioner to extract heat from outside using a compressor, evaporator coils, and condenser coils with refrigerant.

It is most efficient in the spring and fall when temperatures are mild, but it uses much less energy than either a boiler or furnace and it can be used in the summer to cool your home. When properly maintained, a heat pump will last 10-20 years and save quite a bit of money, though it is recommended that you have an emergency heat source for days when the temperature outside gets below 40 degrees F.

Tags: Boilers, Furnaces, Heat Pumps, Heating Systems, Washington DC
Posted in Heating | Comments Off on Pros and Cons of Various Heating Systems in Washington DC

A Question from Washington DC: What is a Gas Furnace Draft Hood?

Wednesday, December 28th, 2011

As every Washington DC heating and air conditioning contractor knows, a draft hood is a necessary part of any gas burning appliance. For a gas furnace in particular it ensures steady air flow to the burners to avoid flares or the pilot light being put out by fluctuation in temperature and air flow.

What the Draft Hood Does

The draft will change in the chimney as exhaust vents towards it – especially when going from cold air to hot. A draft hood is placed above the upper most part of the gas furnace to draw air into the chimney and makes it possible to draw more or less air through the chimney as necessary to create a constant flow.

This makes it possible for the burner to enjoy consistent air flow without any wind gusts or sudden temperature spikes or drops. Hot air, if not put through a draft hood would create a strong air flow through the burners.

A draft hood cools the air as it is released by the burners from 500 degrees F to between 300 degrees F and 350 degrees F. The cooling needs to be carefully calibrated to avoid condensation build up in the chimney however – a problem that occurs when the temperature gets too low.

Maintaining Pressure

The draft hood is a part of a larger system designed to maintain air flow to the chimney. For every cubic foot of gas burned, the furnace needs to have 15 cubic feet of air for combustion and another 15 cubic feet of air for dilution. A draft hood and the rest of the ventilation system make it possible to put a furnace that has many thousands of BTUs in the basement of your home and still supply it with enough air to burn gas and dilute the exhaust before it enters the chimney.

For all of these reasons, if you see your pilot light flickering irregularly, notice a backflow of exhaust or a burning smell in your furnace room, it’s important to call a Washington DC professional who can inspect and repair the problem before it becomes any worse. Not only can gas burner exhaust contain high levels of carbon monoxide, it can be bad for the device and the chimney if it doesn’t vent properly.

Tags: Furnaces, Heating, Washington DC
Posted in Heating | Comments Off on A Question from Washington DC: What is a Gas Furnace Draft Hood?

Washington DC Heating Guide: Why Does Your Furnace’s Pilot Light Keep Going Off?

Wednesday, December 14th, 2011

If you have an older furnace with a gas pilot light and it keeps going out, heating your Washington DC home can become a frustrating process. Not only are you forced to trudge downstairs to light it every time you need heat, but you’re probably starting to worry that there is something wrong – either with your furnace or with your gas supply. Here are some possible reasons for your pilot light shutting off and what you can do about them.

Thermocouple – The thermocouple is used to generate electricity from the gas being burned by the pilot light to power the sensor that keeps the pilot light running. So, if the thermocouple goes bad or gets blocked in some way, the sensor won’t work properly and your pilot light won’t remain lit. Even a small problem with the thermocouple can lead to the valve closing and the pilot light going out.
Gas Pressure – If the gas pressure going to your furnace is too low, due to a leak, pipe problem or another appliance, the pilot light may not have enough gas to stay lit. While it is possible that the problem is not related to gas pressure, anything that affects the flow of gas into your home should be inspected by a professional. If you smell gas, leave the house and call your gas company immediately.
Mercury Sensor – The sensor in your pilot light that maintains the flow of gas to keep it lit can go bad. Keep in mind that these sensors almost always used to contain mercury (and often still do), so you should be careful with them. It’s best to call a professional who can replace and dispose of it properly.
Dirty Burners – Excess dust, lint, rust or sulfur build up can result in blockage of the burner holes. When this happens, gas will flood into the chamber but not light right away. When it does finally light, it will create a small boom or banging sound that will often put out the pilot light. Not only is this inconvenient, it is very dangerous. Fortunately, it can be avoided with annual cleanings of your furnace.

The best way to keep your pilot light lit at all times is to have someone inspect it once a year. If something happens in between, you can usually rule out cleanliness issues and call in a heating contractor to check the thermocouple and sensor.

Tags: Furnace Repair, Heating Repair, Washington DC
Posted in Heating | Comments Off on Washington DC Heating Guide: Why Does Your Furnace’s Pilot Light Keep Going Off?